GK Mechanical Vice Grip. We offer machines, apparatus, testers, tensile grips, test fixtures, clamps, holders, jigs, faces, jaws, extensometers, environmental and humidity chambers, furnaces, baths and custom solutions for unique applications. It is also important to align the specimen perpendicular in the grips so that the peel line is straight across.
A key issue that many people encounter when testing degree peel tests to 3d D, is that both sides of the adhesive specimen can accidentally rub together during testing. A strip of tape is applied to a standard test panel that with controlled pressure from a TestResources Sample Roller. XLW EC Auto Tensile Tester XLW EC Auto Tensile Tester can be used to measure tensile, peeling, deformation, tearing, heat sealing, adhesive, puncture force, opening force and low speed unwrapping force as well as other performance of plastic films, composite materials, soft package materials, plastic flexible tube, adhesives, adhesive tape, label stickers, medical plasters, release paper, protection films, combined caps, aluminium foil, diaphragm, back sheets, non-woven fabrics, rubber, paper, etc.
Fold over 12 mm at one end, adhesive to adhesive to form a tab. If you would rather see the data in astmm and study the peel interface at the same time, we would provide you with our XyLive Software. MED Medical Packaging Tester is professionally applicable to the determination of force properties of various medical packaging materials, with high precision better than 0.
When testing liner side adhesion, the face side adhesive is adhered to a thin polyester film. In a liner-side application, the transfer tape is applied to a strip of 0. If the adherent is set on an angle, that will cause an error.
The tape is applied to atsm substrate with an even pressure using a handheld roller. The tape is applied to the substrate with an even pressure using a handheld roller. This unique standard consists of Methods A through F, identifying ways to measure peel adhesion with degree and 90 degree peel methods.
The information below should help you astm d the basic test procedures and the equipment required to meet this standard with accuracy.
Other sample widths available upon request Effective and simple to use Blade replacement takes mere seconds. Although we can provide astm d with guidance, we recommend you purchase and closely follow the ASTM International testing standard.
The D are small and astm d, perfect for very small load cells testing at low loads. Repeat steps 1 to 6 of Test Method A.
This is because the measured peel force is not astmm for a astm d area of stress. Test Method D can show the amount of force astm d to remove a liner that covers the adhesive side of a tape at a specified peel rate. Rated to 1 kN lbf Maximum specimen thicknesses from 10 mm to 50 mm 0. These characteristics will result in a high variability for the test response which is not a true indication of the real nature of the adhesive bond. Values stated in either SI or inch-pound units are to be regarded separately as standard.
The values stated in each system may not be exact equivalents, therefore, each system must be used independently without combining values in any way. This standard does not purport to address all of the safety concerns, if any, associated with its use.
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Make two passes of the roller using a hand roller of the such as the standard stainless steel panel. Roll firmly. Apply a same size. Remove the liner from the tape and apply to a standard panel as described in Proceed as described second specimen with those of the strip in the test panel. Complete testing as described in NOTE 7In spite of its apparent simplicity, the use of this test method is rather delicate and involves the use of great care in following the Test Method CAdhesion of Double-Coated Tape procedure as written to give coherent and identical results between one laboratory and another, as well as between one operator and another.
Apply this film in Place the so that the roller makes the actual application of the film to the panel into a fixture clamped to the moving jaw of the adhesion double-coated tape. Operate the moving jaw at 5. Continue in accordance with Calculation application of the tape to the film. Trim the film to be as wide Remove the liner. Continue Newtons N , convert to N per 10 mm by converting the pull in accordance with Use actual specimen Specimens of Different Material: width in calculations, 1 Before a meaningful statement can be made about two specific laboratories, the amount of statistical bias observations in 95 out of cases when both observations are between them, if any, must be established with each comparison being taken by the same well-trained operator using the same piece of based on recent data obtained on specimens randomly drawn from one test equipment and the specimens randomly drawn from the sample of the material to be evaluated.
Larger differences may occur under The true value of peel adhesion at ported in See Note 9 and Table 2. It is believed that the precision for the other test methods would be similar. It would probably not apply to Keywords Test Method C.
B To convert the values of the confidence limits to units of measure, multiply the 10 Supporting data are available from ASTM headquarters. Request RR: average of the specific set of data which is of interest by the confidence limits D ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn.
Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phone , fax , or service astm. Open navigation menu. Close suggestions Search Search. User Settings. Skip carousel.
Carousel Previous. Carousel Next. What is Scribd? Uploaded by euse. Did you find this document useful? Is this content inappropriate? Report this Document. Description: norma ASTM.
0コメント